maximum torque造句
例句與造句
- Speed at maximum torque
最大扭矩轉速 - Maximum torque control for field weakening operation of asynchronous motor applied in electric vehicle
電動汽車用異步電機弱磁運行的最大轉矩控制 - Maximum torque per ampere control in permanent magnet synchronous motor direct torque control driving system
電動汽車用永磁同步電動機直接轉矩控制系統 - With reversible motors that are rated for continuous duty , nibco electric actuators provide maximum torque output and longer life
配置可逆電機，適用于連續工作，美國尼伯科電動執行機構能夠提供最大的扭矩輸出和更長的使用壽命。 - Static torque : a fixed location under the maximum torque can be applied to the output shaft . if the torque exerted greater than this value will be separated for damage
靜態扭矩：在固定位置下最大扭矩可施加到出力軸上。如果施加的扭矩大于這個數值，則會損壞分割器。 - It's difficult to find maximum torque in a sentence. 用maximum torque造句挺難的
- In this paper , the maximum torque per ample ( mtpa ) control in permanent magnet synchronous motor ( pmsm ) direct torque control ( dtc ) driving system was studied
摘要在永磁同步電動機直接轉矩控制和最大轉矩電流比控制理論基礎上，研究了永磁同步電動機直接轉矩控制驅動系統最大轉矩電流比控制的實現。 - Based on artificial neutral network control theory , a mimo neutral network pid speed regulator realizing the maximum torque with minimum current is conformed for a pmsm drive system
本論文在人工神經網絡控制理論的基礎上，針對永磁同步電動機矢量控制系統，構造實現最大轉矩電流控制的mimo神經網絡pid速度控制器。 - By adjusting the fuel rectifying screw and then increasing the fuel quantity per cycle , the loss of the maximum power of e30 engine ca n ' t exceed 10 % of the maximum power of diesel , and the loss of the maximum torque can be controlled within 2 percent
通過旋出油量校正螺釘，增大燃料供給量，可以使e30混合燃料發動機的最大功率損失控制在10以內，最大轉矩?fù)p失控制在2以內。 - The instantaneous torque measurement system has been improved , which uses slip ring to transmit signal , improved measuring accuracy and stability , the mechanism of occurring of instantaneous maximum torque has been understood during changeover of the main engine
改進了集流環傳輸信號的瞬時扭矩測量系統，提高了測量精度和穩定性，進一步認清了在主機切換過程中瞬時扭矩的極大值產生的機理。 - And it analyses the power factor in different conditions via the fourier anlysis of the stator current and voltage . then , it sets up the simulating model for maximum torque / current ratio . the torque can be controlled by controlling the angle of stator current vector
在矢量控制實現的基礎上,采用傅立葉分解分析電機的相電流和相電壓,得到矢量控制系統中電壓和電流的基波分量和相位角,進而判斷電機的功率因數,分析在不同控制情況下電機的功率因數狀況。 - According to the relationship of the angle of the maximum torque and the q axis , the reluctance torque for salient pmsm is made full use of and the sator current amplitude is reduced by a large percentage , so that the system robustness is greatly increased . at the speed loop , this paper presents a single value model algorithmic control strategy which is the simplied form of normal model algorithmic control and has less computation work than the latter , so the real - time performance is very good
對于嵌入式pmsm ，根據在電流幅值一定的條件下最大輸出轉矩與(為等效電流矢量和q軸之間的相位角)之間的關系，將磁阻轉矩轉換為輸出轉矩從而提高了輸出轉矩，改善了系統的控制性能；在速度環采用單步模型算法控制，其計算量比較少，提高了系統的實時性和魯棒性。 - Based on the torque - speed characteristic curve of induction motors , analyses were done on changes in slip with an variation in frequency when an induction motor drives different kinds of loads , including those with constant torque , constant - maximum torque , variable torque ( except fans and pumps ) and constant power , as well as fans and pumps , the formulas to calculate the slip and the speed under different frequencies and loads were presented
摘要以異步電動機機械特性曲線為基礎，分析了變頻調速異步電動機在拖動恒轉矩負載、恒最大轉矩負載、變轉矩（非風機和泵類）負載、恒功率負載以及風機和泵類負載時，轉差率隨頻率變化的規律。